Series FH-480 Sanitary Filter Housing
VQ-FH480
Filter housing, flow 5 to 60 m³/h, rating 0.2 to 20 micron.
- FLOW
- 5 to 60 m³/h
- RATING
- 0.2 to 20 micron
- DESIGN PRESSURE
- 10 bar
- TEMPERATURE
- -10 to +150 °C, steam sterilisable
Why it is specified
A housing is half an answer. Every selection is quoted with the element, the seal material and the differential pressure at the design flow, so the running cost is on the quotation and not discovered later.
Typical applications
- Condensate protection
- Cooling tower side streams
- Paint and coating transfer
- Pre-filtration ahead of cartridge stages
Options and executions
- Davit arm for the lid
- Differential pressure gauge with a switch
- Jacketed shell for viscous media
- Material certificates to EN 10204 3.1
The full table.
Figures cover the whole series. The variant table below narrows them to a part number.
PERFORMANCE
- Design flow
- 5 to 60 m³/h
- Filtration rating
- 0.2 to 20 micron
- Clean pressure drop
- 0.04 to 0.14 bar
- Recommended change-out
- 1.0 bar differential
- Element count
- 1 to 5 code 7 elements
MATERIALS
- Shell and lid
- 1.4404 stainless steel, electropolished
- Internals
- 1.4404 stainless steel, electropolished
- Lid seal
- Silicone, platinum cured
- Internal finish
- Ra 0.4 micron, electropolished
CONNECTIONS AND RATINGS
- Inlet and outlet
- DN40 to DN80
- Vent and drain
- Fitted as standard
- Design pressure
- 10 bar
- Temperature range
- -10 to +150 °C, steam sterilisable
- Closure type
- Tri-clamp with a sloped tube sheet
Stocked frame sizes.
| PART NUMBER | SIZE | CONNECTION | DESIGN FLOW | MATERIAL |
|---|---|---|---|---|
| VQ-FH480-10 | 1 element | DN40 | to 12 m³/h | 1.4404 |
| VQ-FH480-20 | 3 elements | DN50 | to 34 m³/h | 1.4404 |
| VQ-FH480-30 | 5 elements | DN80 | to 60 m³/h | 1.4404 |
FH-480, DS-FH-480
The datasheet is issued with the selection rather than downloaded blind, so the figures that arrive are the ones for your duty point. Ask for it with the quotation and it comes back as a PDF.
What is in it
- Selection data and the limits each figure applies at
- Dimensional drawings for every size in the variant table
- Materials of construction and the compatibility notes
- Installation, commissioning and maintenance intervals
- Spare parts list with the part numbers
Elsewhere in the catalogue.
FH-400
Stainless steel single-bag filter housing with a swing-bolt closure and an internal restrainer basket, for coarse and medium filtration on process and utility lines.
CF-250
Multi-round cartridge housing with a clamped closure, for fine and final filtration where the element is the specification and the housing is the frame around it.
FH-220
Filter housing, flow 10 to 90 m³/h, rating 1 to 800 micron.
FH-340
Filter housing, flow 20 to 240 m³/h, rating 0.5 to 100 micron.
Quote the FH-480 for your duty.
Send the process data and the line size. The quotation comes back with the selection, the calculation and the lead time on the stocked variants.
Vanteq Industrial is a fictional company created for demonstration purposes. This product does not exist. The specifications, performance figures, materials and datasheet references on this page are illustrative and must not be used to select, size or buy equipment.