Series CP-180 Close-Coupled Pump, High Head
VQ-CP180
Close-coupled centrifugal pump, flow 4 to 90 m³/h, head 20 to 78 m.
- FLOW
- 4 to 90 m³/h
- HEAD
- 20 to 78 m
- PRESSURE
- PN16
- TEMPERATURE
- -20 to +110 °C
Why it is specified
The close-coupled build puts the impeller on the motor shaft, so there is no baseplate, no coupling and no alignment to lose. It is the shortest pump on the shelf for a given duty, and the one that fits in the plant room that was designed without one.
Typical applications
- Boiler feed, low pressure
- Clean-in-place supply
- Cooling water circulation
- Pressure boosting
- Process water transfer
Options and executions
- ATEX zone 2 execution
- Double mechanical seal
- Flushing plan 11 or 21
- Frequency converter, motor mounted
- Performance test to ISO 9906 grade 3
The full table.
Figures cover the whole series. The variant table below narrows them to a part number.
PERFORMANCE
- Capacity
- 4 to 90 m³/h
- Differential head
- 20 to 78 m
- Speed
- 2,900 rpm, 50 Hz
- Impeller type
- Closed radial, single entry
- NPSH required
- 1.8 to 4.6 m
- Motor power
- 3 to 30 kW
MATERIALS
- Casing
- EN-GJL-250 cast iron
- Impeller
- 1.4408 stainless steel
- Shaft
- 1.4021 stainless steel
- Shaft seal
- Single mechanical seal to EN 12756
- Gasket
- Graphite laminate, non-asbestos
CONNECTIONS AND RATINGS
- Suction
- DN65
- Discharge
- DN40
- Pressure rating
- PN16
- Temperature range
- -20 to +110 °C
- Design standard
- EN 733 hydraulic duties
Stocked frame sizes.
| PART NUMBER | SUCTION / DISCHARGE | CAPACITY | CASING | MOTOR |
|---|---|---|---|---|
| VQ-CP180-10 | DN65 / DN40 | to 36 m³/h | EN-GJL-250 cast iron | 3 to 7.5 kW |
| VQ-CP180-20 | DN80 / DN50 | to 62 m³/h | EN-GJL-250 cast iron | 7.5 to 18.5 kW |
| VQ-CP180-30 | DN100 / DN65 | to 90 m³/h | EN-GJL-250 cast iron | 15 to 30 kW |
CP-180, DS-CP-180
The datasheet is issued with the selection rather than downloaded blind, so the figures that arrive are the ones for your duty point. Ask for it with the quotation and it comes back as a PDF.
What is in it
- Selection data and the limits each figure applies at
- Dimensional drawings for every size in the variant table
- Materials of construction and the compatibility notes
- Installation, commissioning and maintenance intervals
- Spare parts list with the part numbers
Elsewhere in the catalogue.
CP-150
Single-stage, back pull-out end-suction pump to EN 733, for clean and lightly loaded liquids in process, cooling and transfer duty.
MD-80
Close-coupled sealless centrifugal pump with a synchronous magnetic coupling, for aggressive, toxic and expensive media where a dynamic seal is not acceptable.
CP-120
Close-coupled centrifugal pump, flow 2 to 48 m³/h, head 8 to 42 m.
CP-125
Close-coupled centrifugal pump, flow 2 to 60 m³/h, head 8 to 52 m.
Quote the CP-180 for your duty.
Send the process data and the line size. The quotation comes back with the selection, the calculation and the lead time on the stocked variants.
Vanteq Industrial is a fictional company created for demonstration purposes. This product does not exist. The specifications, performance figures, materials and datasheet references on this page are illustrative and must not be used to select, size or buy equipment.